Our living room has this one area that’s been tough to figure out. I wanted a piece of furniture that wouldn’t take up too much space, but could provide seating. Something that could be flexible in case we wanted to open up the two rooms, but wouldn’t feel too haphazard. Craig to the rescue.
These two chairs were listed for $75 each. Here’s what I liked: The shape. The details. The portability. The potential.
Here’s what I didn’t like… the price. I responded to the seller and asked if the price was negotiable. I ended up getting both chairs for $100. Not bad considering this same chair goes for $339 at Restoration Hardware. and $329 at Wisteria.
So onto the business of making gross into glam. With all of these projects, I come away with a list of lessons learned. These chairs are no exception. First lesson learned? There’s a special place in DIY hell for nailheads and staples.
Supplies (affiliate links included for your convenience):
- Fabric similar to this
- Staples, staples and more staples. I used both 1/4″ and 3/8″.
- Staple gun. (Update… I’ve since purchased this pneumatic stapler so it requires a compressor but it’s changed my upholstery life… SO much easier!!)
- flat head screw driver/ needle nose pliers for staple and nail removal (Update: I prefer this tool specifically for staple removing.)
- hot glue gun
- double welt cord or gimp to cover staples
- spray paint
I wanted to reupholster. Another reason I like this style is that there’s not a ton of fabric which keeps the project cheaper. In order to get the fabric off, I had to use a flat head screw driver and some needle nose pliers to pull out Every. Single. Nail head. And staple.
Make certain to take lots of pictures before and save every piece of fabric you remove…. these will be your templates for the new fabric. Second lesson learned? Fabric might not look that bad, but then you take it off and realize how disgusting it was. Hallelujah for reupholstering.
With fabric removed, time to paint. I wanted a super shiny finish to complement the super shiny coffee table. I opted for spray paint because of the nooks and crannies on these chairs, but I still haven’t quite nailed my spray painting routine. Specifically, I have no idea where people spray paint without spray painting everything within 12 square feet. For this project, I set up shop right outside our basement. Figured I’d be out of the basement and technically outside for ventilation, but still within the confined space of the bilco stairwell so the spray wouldn’t blow everywhere. It was a little tight so I coudn’t reach everything thoroughly; I have to go back and touch up with a paintbrush to get at the legs and some other tight corners. (I didn’t bother taping off the foam as you can see…. fabric was going over it and saved me the hassle.) Oh, Lesson 3: red spray paint makes a mess of things. Apologies… no pictures of this stage; I was hoping to keep all of this on the DL so Mark wouldn’t laugh at me for being such a DIY disaster. But here’s a glimpse of the color:
I let the chairs sit for a good 48 hours before moving on to upholstering (and to rest my now red and aching fingers after the whole nailhead/ staple removal process). The upholstering was actually the easiest part of this whole project. Using the old nasty fabric as a template, I traced each piece onto my new fabric leaving plenty of extra room for stapling.
I made sure to focus on where the template was laid out on the fabric so the pattern wasn’t misaligned and crooked on the chairs.
Check out this tutorial for another explanation of the process in case I miss any steps. I started with the seat, being careful to center the chevrons. I put in a few staples on the back, then moved around, pulled the fabric straight and taught and and stapled the front down. Then I filled in around the edges making sure chevrons were straight and fabric was tight. I used the same process for the arms. (My foam was in good shape so I didn’t have to replace it; if it had needed replacing, I would have used the old foam as my guide and cut new foam for the seat and arms.)
The back. Oh, the back threw me, but by the second chair I’d figured it out. The chairs I bought had tufting (the little buttons). I wanted something cleaner so was getting rid of the tufting. When I took it apart, there was a layer of fabric and batting on the backside, and a layer of cardboard (to hold the concave shape), foam and fabric on the front. I replaced the batting and the foam. First I stapled the fabric for the back.
Then, I layered the batting, cardboard, foam and fabric and stapled all of these on top. Kind of like a fabric sandwich with batting, cardboard and foam in the middle. I found that a few staples on the top and then a few on the bottom held all the layers in place so I could go around pulling it all tight and stapling the edges.
Phew. This was my first glimpse of what these chairs would look like, and I’m digging them. (Let’s be honest, you could stick a chevron fabric on a toilet bowl and I might put it in my living room.) I trimmed the fabric edges as close to the staple line as I could and set up the sewing machine for the double welt cord.
I was hoping to find ready made double welt cord and use a double welt sewing machine foot, but alas… Jo Ann fabrics didn’t have the cord and the sewing machine foot needed to be ordered. So thanks to Kate over at Centsational Girl, I converted my single cord to double cord. My seams are still a little shaky and it’s not as neat and tidy as a professional, but it does the trick of covering all those unsightly staples and frayed fabric.
With my hot glue gun, I wound the cord around the chair to cover all the staples. I screwed up on the first chair by not winding it around the arms of the chair… you’d never notice, but it’s much cleaner to wrap the whole length of the seat since it leaves only the one point where you’ve cut the cord.
Last lesson learned: this wasn’t as easy or quick as I was expecting, but… it wasn’t hard either. And I’m thrilled with the results. Sure, there are always little parts of these projects that I wish I’d done differently or want to go back and change, but I probably won’t. And no one will notice the frayed cord under the right arm or the sliver of fabric you can see behind the welt on the back.
Cost of these chairs retail= $340 on average.
Cost of reupholstering=$250.
Cost for these= Maybe $150 all in. For both.
I love what these do for the living room space and after a dinner party we hosted this weekend, it was great to have the extra seating just from a functional point of view. And… Eleanor now has more seating for her stuffed animals and dolls, so there’s that! Here’s another before/ after to save you the scrolling!
Don't miss a post! Sign up for email or RSS updates!